Fitting A Cat Flap

Fitting a cat flap can be a bit daunting however it's actually quite simple with the proper instructions. Decide how high you'd like the flap to be (normally it's located at belly height). Mark this point on your door, and use the template provided as a guide when drilling.

If you have a kitten, or a young kitten you can prop the door open very slightly and gradually encourage it to pass through. Reward the kitten every time it goes through.

Measure the Door

A cat flap is a wonderful option to let your pet come and go inside and out of your home as it wants. This can help keep your cat healthy by ensuring that it is getting exercise as well as being able to get back inside if trapped outside in bad weather, particularly during the winter. It also can reduce the amount of time you need to allow it in or out and can protect your home by letting you know when it has gone out.

It is crucial to make sure that the cat flap is installed correctly in order to prevent your pet from being pushed through it or escaping by other animals (e.g. dogs). It is essential to measure the height of your pet's belly and the entrance to your home to make sure that the flap is at the right height. If your cat is larger or shorter than the average, you can alter the position of the flap by moving it upwards or downwards by a small amount.

Next, use a spirit-level to mark the center of the door. This is where you'll install the flap. Then, using the markings as a guideline, cut out the form of your flap using a jigsaw. After you've cut the door, sand the edges of the door to create smooth surfaces. You can then drill any fixing holes needed.

Installing a cat flap ought to not take more than two hours. The process can be slightly more difficult if you have to install it on a uPVC door or a composite one. This is because composite doors come in different thicknesses, which can impact the way the holes are cut. We always recommend to contact a professional if this is your first time working with glass.

Measure Your Cat

You can save yourself hours of ignoring the cat's meows to be allowed in or out. This is particularly helpful if you are at work most of the day and your cat flap installer near me has to stay inside waiting until you get home in all weathers.

If you are planning to install a cat flap in your door, it is essential that you determine the size of your cat prior to beginning the task. It might seem like a straightforward task, but it is crucial to make sure you measure the right measurements. In the event that you don't, your cat might find it difficult to use.

First, ensure that your cat is calm and not anxious prior to taking the measurements. You'll need to hold them in a way that they cannot move and also ensure that the ruler or measuring tape is flat against their body, not bending in any place. You can get a precise measurement by keeping the measuring tape or ruler flat against the body of the animal from the top to the bottom.

Once you have the measurement of your cat, it's time to take a look at the door and decide where you want to place the flap. It is advisable to position the flap in the middle of your cat's belly as it will allow them to get through it without much effort. This will also stop the flap making lots of noise when it opens and closes.

You should also take into consideration the thickness and structure of the uPVC door or composite. While timber doors are all of a similar thickness, uPVC and composite doors are different in their overall design and this can make the installation of a cat flap more complicated because you must make sure that the hole you cut is the right size for your pet.

It is also worthwhile studying the instructions included with the double glazing cat flap flap kit to find a template drawing that can be used to determine the position of the hole in the door. This will enable you to determine where the hole should be placed and ensure that the template is set correctly on the door. It is also beneficial to use a spirit-level to ensure that the template is placed in a straight line against the door.

Cut the Flap

Before you can put in your cat flap, you'll need to cut the door panel in order to make it large enough for it. It's a challenging task and it is recommended that you engage a professional to assist you if you do not have the knowledge or skills. It is also recommended to review the directions that come with the kit to discover how to do this correctly.

You can use the height of the cat's or kitten's stomach as a guide. A good rule of thumb is to put the cat flap about 10-15 centimeters away from the ground since this is the typical height of the cat's belly. This will let your cat pass through the flap with ease and make it more difficult for other cats or naughty neighbors to get in or out.

The position of the cat flap on the door with a pencil. If your kit comes with the template you can place it on the door. Utilize the markings on the template to drill holes at every corner. Then, you should be able to cut out the template and replace it with the cat flap.

You can install the cat flap yourself in an uPVC or wood door If you're comfortable using the jigsaw. Make sure you don't cut through any of the door's mullions, or vertical rails. You can use a jigsaw to cut the panel into a square or a circle according to the design of your cat flap. Be patient and don't try to make the jigsaw cut faster.

Once the hole is cut, carefully place the cat flap in its new place of residence. Make sure it's firmly secured. If it features caps on the screws, then place them onto the protruding screws. After the screws are installed smooth the edges and apply sealant to any gaps. This will stop the entry of draughts into your home.

Fit the Flap

If you have an ordinary cat flap, you can help your pet to go through it by placing a small amount cat food on the top of the door. Alternatively you can try pushing the cat through using your hand or a stick. Once your pet has become used to moving through the flap, it will be in a position to move at will. This will allow you to let it in and out as it wishes.

It is possible to fit the flap inside the UPVC doors or glass door, however it may not be as simple as installing one in a wooden external door. This is because the UPVC doors and certain types of glass doors don't have a uniform thickness. This could have an enormous impact on how you cut out the flap's hole and whether the flap will fit correctly after installation.

Based on the type of cat flap you pick It could include a mounting kit as well as a template that will show you exactly where to drill holes for it. If the kit doesn't include a template, you are able to make one yourself. When cutting, it's crucial to keep the jigsaw from being pushed too to the point that you make a larger hole than necessary in your door.

The majority of fitting cat flap in upvc door panel flaps are rectangular or square in shape, but there are also some which are circular, and are typically more difficult to place. If you have a circular flap, make sure that the hole is located in the correct place on the door. In the event that it is not, the cat might not be able to use it, and might be outside all day (or at night).

Some cat flaps have locks that allow you to manage when your cat comes and goes. These are very helpful when you're worried about your cat going out at night and coming back in due to the darkness, or you're working all day. The lock can be engaged for entry or exit and some locks can be locked in both directions, allowing you to shut the door completely, which is especially beneficial for older or ill cats who aren't willing to go out in the rain.